Roof pitch and slope
Roof Slope

Last updated November 17, 2026 · Method · Corrections
Roof slope is vertical rise over level run. Rise-in-12 counts rise units per twelve level units. Degrees, percent slope and rise-in-12 state the same measured slope in three units. Use level run, not full span or sloped rafter length. Keep each plane's measured ratio before checking a covering's range. A slope number does not inspect the deck or show drainage.
Sections7
Roof slope is vertical rise over level run. Rise-in-12 counts rise units per twelve level units. Degrees, percent slope and rise-in-12 state the same measured slope in three units. A slope ratio helps compare planes and check a covering's stated range. It does not approve a material or show roof condition.
Roof slope: rise and run on one plane
Picture one roof plane as a right triangle. The vertical leg is rise. The horizontal leg is level run. The sloped side is the roof surface length. Slope always pairs rise with level run, not with the sloped edge.
For rise-in-12 notation, the run is fixed at twelve level units. A 4:12 slope rises four units for every twelve level units along the eave. The Asphalt Roofing Manufacturers Association bulletin states slope as two inches per foot (2:12) in its shingle limits.
Main roofs, porches and shed roofs can each have their own slope. Record them separately. A steep main roof does not set the porch ratio. The roof pitch calculator converts one plane at a time from rise and run or a known angle.
Roof slope: pitch, percent and degrees
The same measured slope can appear in several units. Each must come from one measured ratio. Do not copy a number from one unit into another field without converting.
| Form | Meaning | Example at 6:12 |
|---|---|---|
| Rise-in-12 | Rise per 12 level units | 6:12 |
| Percent slope | Rise ÷ run × 100 | 50% |
| Degrees | Angle above level | About 26.57° |
Scroll for more →
Percent slope and rise-in-12 both use level run in the denominator. A 45-degree angle gives 12:12 and one hundred percent slope. That is steep, but it is not a vertical wall. The roof pitch chart lists integer rise-in-12 rows with matching degrees and area factors.
Steeper slopes shed water faster than shallow ones. ARMA notes slower drainage on lower slopes in the same bulletin. Drainage speed is a reason to treat low-slope planes separately. It does not by itself pick a product.
Roof slope: read a ratio from records
Use a measured plan, roof report or accessible deck measurement. Keep the source with the ratio so the unit basis can be checked.
- Pick one roof plane and name it on the sketch.
- Find vertical rise and horizontal run in the same unit.
- For a symmetric gable, use half the full eave span as level run, not the whole span.
- Do not use sloped rafter length as run; it belongs to surface length, not the slope ratio.
- Divide rise by run, multiply by twelve for rise-in-12, or enter the pair in the pitch calculator.
Read how to calculate roof pitch when the record uses degrees, percent or unfamiliar labels. Unknown slope stays unknown until a valid measurement exists.
Roof slope: area and the pitch factor
Roof area estimates often start from a level footprint. The sloped surface is longer than its horizontal projection. For ratio t equal to rise divided by level run, the area factor is the square root of one plus t squared.
This factor applies only when the input is level plan area. A report that already lists sloped surface needs no second multiplier. The roofing calculator keeps those modes apart so pitch is not applied twice.
At 12:12 the factor is about 1.4142. That value comes from the stated formula with t equal to one, not from a typical roof guess. Rounded chart rows are for quick checks. Keep the measured ratio for the actual plane.
Roof slope and covering limits
A numeric slope does not approve shingles, metal or a membrane. Each system has its own documents and local rules. Slope is one input among deck, layers and junction details.
ARMA states that shingles must not be applied below 2:12. It allows special procedures only from 2:12 up to less than 4:12. ARMA says to follow the shingle and underlayment manufacturers' instructions for lower-slope work.
Measure each plane before comparing products. Read minimum roof pitch for shingles and low pitch roofing materials for assembly checks on the actual ratios.
Transitions between a shallow section and a steeper main roof need their own detail. ARMA calls for carrying low-slope underlayment methods at least twenty-four inches onto the steeper plane. Keep those junctions in the written scope.
Return to the roof pitch calculator when you need conversions, then carry the exact ratio into material guides and area worksheets.
Frequently asked questions
What is roof slope in simple terms?
Rise-in-12 fixes run at twelve level units. Percent slope is rise divided by level run, times one hundred. Degrees come from the same rise-and-run pair through trigonometry.
Is roof slope the same as roof pitch?
Pitch and slope both mean the rise-to-run ratio for a plane. Check whether the drawing labels level run or full span before you compare the number to a product range.
Can one house have several roof slopes?
Yes. A steep main roof, a shallow porch and a shed roof can each have a different ratio. List each plane with its own slope and area. Do not average unlike slopes for a material check. The pitch calculator accepts one conversion at a time.
Does a steeper slope always mean more roof area?
Steeper slopes increase the area factor for a matching footprint. A measured sloped surface already includes that geometry. Apply the factor only when the input is level plan area. Adding the factor to an existing surface total counts pitch twice.
What roof slope is too low for asphalt shingles?
ARMA states that shingles must not be used below 2:12. From 2:12 to less than 4:12, its bulletin allows shingles only with defined underlayment methods. Read the exact product instructions and local rules before treating a plane as shingle-suitable.
Verdict: keep slope measurement separate from material choice
Record each plane's measured slope before you open covering guides or area tools.